Flange Adapters, Back-up Rings, MJ Adapters, and MJ Kits
Molded elbows, tees, and MJ adapters are available through 8 inch diameter. Saddles and tapping saddles are also available for a broad range of sizes. Click on the link below to view and print a copy of the submittal sheet.
IPS Flange Adapter
DriscoPlex® HDPE Molded Fittings are available to meet your needs in compliance with ASTM D2513, D3261, F2880, F2897, F2880 and AWWA C906 product standards.
Made in the USA and produced from high quality HDPE material, DriscoPlex® Fittings are manufactured from NSF-61/Annex G approved PE 4710 resin as listed in PPI-TR4.
Not recommended for use with Gas Distribution Applications.
DriscoPlex® PE Fittings Advantages:
✓ Durable
✓ Leak Tight
✓ Excellent Flow
✓ Easy Install
✓ Light Weight
✓ Impact Resistant
✓ Fusibility
✓ Corrosion Resistant
✓ Corrosion Resistant
✓ Chemical Resistant
✓ Life Cycle Cost
✓ Toughness
✓ Environment
✓ Life Cycle Cost
✓ Toughness
✓ Environment
IPS Beveled Flange Adapter
DriscoPlex® HDPE Molded Fittings are available to meet your needs in compliance with ASTM D2513, D3261, F2880, F2897 and AWWA C906 product standards.
Made in the USA and produced from high quality HDPE material, DriscoPlex® Fittings are manufactured from NSF-61/Annex G approved PE 4710 resin as listed in PPITR4.
DriscoPlex® PE Fittings Advantages:
✓ Durable
✓ Leak Tight
✓ Excellent Flow
✓ Easy Install
✓ Light Weight
✓ Impact Resistant
✓ Fusibility
✓ Corrosion Resistant
✓ Corrosion Resistant
✓ Chemical Resistant
✓ Life Cycle Cost
✓ Toughness
✓ Environment
✓ Life Cycle Cost
✓ Toughness
✓ Environment
Mechanical Joint Adapter and Kit
DriscoPlex® HDPE Molded Fittings are available to meet your needs in compliance with ASTM D3261 and AWWA C901 and C906 product standards.
Made in the USA and produced from high quality HDPE material, DriscoPlex® Fittings are manufactured from NSF-61 approved PE 4710 resin as listed in PPI-TR4.
DriscoPlex® PE Fittings Advantages:
✓ Durable
✓ Leak Tight
✓ Excellent Flow
✓ Easy Install
✓ Light Weight
✓ Impact Resistant
✓ Fusibility
✓ Corrosion Resistant
✓ Corrosion Resistant
✓ Chemical Resistant
✓ Life Cycle Cost
✓ Toughness
✓ Environment
✓ Life Cycle Cost
✓ Toughness
✓ Environment
Molded Wall Anchor
DriscoPlex® HDPE Molded Fittings are available to meet your needs in compliance with ASTM D2513, D3261, F2897 and AWWA C901 and C906 product standards.
Made in the USA and produced from high quality HDPE material, DriscoPlex® Fittings are manufactured from NSF-61/Annex G approved PE 4710 resin as listed in PPI-TR4.
DriscoPlex® PE Fittings Advantages:
✓ Durable
✓ Leak Tight
✓ Excellent Flow
✓ Easy Install
✓ Light Weight
✓ Impact Resistant
✓ Fusibility
✓ Corrosion Resistant
✓ Corrosion Resistant
✓ Chemical Resistant
✓ Life Cycle Cost
✓ Toughness
✓ Environment
✓ Life Cycle Cost
✓ Toughness
✓ Environment